Auto news on Youtube Jun 29 2018

Today we're taking a look inside the BMW Spartanburg plant in South Carolina, USA. In case you didn't know already, this is where most of BMW's X vehicles are made, except the X1 and X2 which are based on a different architecture and built in Europe or China, depending on the case. Since the world is going bananas for SUVs these days, BMW had to enlarge the production capacity of the Spartanburg plant which is now the largest in the world for the BMW Group, making about 450,000 cars a year.

For more infomation >> AUTONEW UPDATE-The Production Process of the BMW X4 in Spartanburg. - Duration: 6:24.

-------------------------------------------

【♀ 冠儀試車日記】突破極限！BMW韓國仁川駕訓體驗！ - Duration: 21:55.

For more infomation >> 【♀ 冠儀試車日記】突破極限！BMW韓國仁川駕訓體驗！ - Duration: 21:55.

-------------------------------------------

BMW E36 - ETS 2 - Euro Truck Simulator 2 - Duration: 6:05.

For more infomation >> BMW E36 - ETS 2 - Euro Truck Simulator 2 - Duration: 6:05.

-------------------------------------------

Đánh Giá XE BMW M8 2019 Màu Xanh Rêu Đặc Biệt - Duration: 1:18.

For more infomation >> Đánh Giá XE BMW M8 2019 Màu Xanh Rêu Đặc Biệt - Duration: 1:18.

-------------------------------------------

BMW e30 m52 turbo winter maintenance. S02E07 Dyno Time! - Duration: 7:00.

Welcome back to Sipa's garage.

This time we had little change of plans and I'm taking my car to be dyno tuned.

And this is only few days after the track day, so I haven't got time to do anything for the car.

So lets hope that the duct tape holds and everything works as it should.

So lets go to the DTC and see what happens.

The normal cruising speed areas of the maps were tuned first.

But yeah. This is unbelievable boring to watch and it took hours to tune the vacuum areas of the map.

So lets jump straight to the power pulls.

Well yeah it gave quite big power numbers!

I was bit surprised of the numbers.

IT was even.. It was over 500hp from the rear wheels.

I could even try to apply the 500whp.net club.

But yeah. They wont probably accept me after those video response they made for my bimmer party video.

Or something like that.

But just to annoy them, I could try to apply.

But anyways, those are just the internet dick growing numbers.

Main goal was to tune the car, and I will later flatten out the torque curve by adjusting boost levels.

The car will be much nicer to drive without that spike in the torque curve.

After that the hp number will be bit over 500 or something like that.

Goal is to have wide flat torque area, which is good for the cars performance.

To get that I will need to drop the boost to 0.8 bar at the highest torque RPM and the raise it back to the 1.2 bar bit later.

So I need to do that kind of boost map.

And yeah the VANOS wasn't working properly. We needed to do pulls with vanos on and vanos off.

That's why there was to power graphs.

Because the vanos is bit broken.

For some reason the vanos doesn't return to normal position when doing power pull.

It does it only after I lift off the throttle.

Otherwise it works ok. But when it's in use, there is some power missing at the top end.

So we needed to do top RPM tuning without vanos activated.

I need to figure out what is wrong with it and probably while doing that I will convert it to PWM controlled.

But the next video of this car will probably be after the bimmerparty. Don't know.But we will see.