Required tools: Wire brush Brake cleaner Copper grease Anti-squeal paste Drive socket # 13 Wheel impact socket #19 Ratchet wrench Torque wrench Brake caliper wind back tool Crow bar Wheel chock
1. Unscrew the brake fluid reservoir cap.
2. Unscrew the wheel bolts. Use wheel impact socket #19.
AUTODOC recommends: To avoid injury, hold up the wheel when unscrewing the bolts.
3. Raise the front of the car and secure on supports.
4. Spread the brake pads. Use a crowbar.
5. Disconnect the ABS sensor electric socket. Disconnect the brake pad wear sensor plug. Remove the ABS sensor connector. Remove the connector of the brake pad wear sensor.
Please note! Some cars are not equipped with the brake pad wear sensor.
6. Release the ABS sensor cable from the holder on the brake caliper.
7. Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench.
8. Remove the brake caliper.
AUTODOC recommends: Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system. Make sure that the brake caliper is not hanging on the brake hose. Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
9. Remove the brake pads.
10. Clean the brake pad clips. Use a wire brush. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
11. Treat the brake caliper bracket where it contacts the brake pads. Use anti-squeal paste.
AUTODOC recommends: Make sure the disc surface is clean before installing the pads.
12. Install new brake pads.
AUTODOC recommends: Make sure the pads are installed with linings facing the disc.
13. Press in the brake caliper piston. Use brake caliper wind back tool.
14. Install the brake caliper and fix it. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
AUTODOC recommends: Without starting the engine, press the brake pedal several times until you feel significant resistance.
15. Install the ABS sensor cable in the holder on the brake caliper.
16. Connect the ABS sensor electric socket. Connect the brake pad wear sensor plug.
17. Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
18. Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
19. Screw in the wheel bolts. Use wheel impact socket #19.
AUTODOC recommends: To avoid injury, hold up the wheel when screwing in the fastening bolts.
20. Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 nm torque.
AUTODOC recommends: Check the brake fluid level in the expansion tank and refill if necessary.
21. Tighten the brake fluid reservoir cap.
AUTODOC recommends: Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.
For more infomation >> Jak wymienić przednie klocki hamulcowe w FIAT 500 ABARTH (312) [TUTORIAL AUTODOC] - Duration: 4:44. 
For more infomation >> Cum se înlocuiește placute frana din față FIAT 500 ABARTH (312) [TUTORIAL AUTODOC] - Duration: 4:44. 
For more infomation >> Wie FIAT 500 ABARTH (312) Bremsbeläge vorne wechseln [TUTORIAL AUTODOC] - Duration: 4:44. 
For more infomation >> Πώς αντικαθιστούμε δίσκοι εμπρόσθιας φρένων σε FIAT 500 ABARTH (312) [ΟΔΗΓΊΕΣ AUTODOC] - Duration: 5:16. 
For more infomation >> Come sostituire dischi freno anteriore su FIAT 500 ABARTH (312) [TUTORIAL AUTODOC] - Duration: 5:16. 
Không có nhận xét nào:
Đăng nhận xét