Auto news on Youtube Sep 29 2018

Hey, guys.

Today, I'm here with the Barricade tubular fender flares fitting all '07 to '18 two-door

and four-door JKs.

This is going to be for the guys out there looking for a tough off-road look, some better

protection for the side body of your JK, as well as a flat fender to allow more up travel

for larger wheels and tires.

This is going to be your most affordable option at the moment at roughly $350 for either the

front or the rear and at roughly $700 for a set of all four.

Compared to other options on the page for only the front, those are going to cost roughly

the same amount as all four of these so, I think you're getting a great deal out of these.

Install will be a strong one out of three wrenches and there's not going to be any drilling

required, however, you might have to wrestle the fender on there to get all of the bolt

holes to line up.

So, so speaking of the install, let's jump into that now.

So, our first step to remove our stock fender is to remove the six bolts holding it on.

So, we're going to be removing these six 10-millimeter bolts holding on our fender flare up around

the liner.

So, after we remove those six bolts, we need to unplug our side marker light harness.

You can just pull the inner fender liner back, and there should be a tab and you can pull

that out.

So, this part's not going to sound great, but all you have to do is pull off your fender

and pull the pop clips out of the body.

So after that, you can rest your fender on the wheel and disconnect your side marker

light harness.

So, we're not going to be reusing this harness, so we can fully unclip it.

With our harness removed, we can fully remove our fender assembly.

So, in order to remove our rear fender, we have four pop clips inside of our inner fender

liner that we're going to pull out so we can remove the full fender.

I'm using a trim removal tool.

So now, we can remove our rear fender just like we did our front and just pull it out.

So after pulling the fenders off, just make sure if you do have any remaining clips, that

you remove those so we can install our new ones.

You can just take a trim removal tool and they should pop out pretty easy.

Just be careful because these ones are crazy.

So, there are two ways that you can go with a fender flare.

You can choose a plastic option like the stock one.

However, when you're off-road, if you do hit something, they can bend or break.

But the good thing about that is that they will just pop right off and not transfer any

of that energy into your body, causing any extra damage that you might not want.

Or you could go with a tubular fender like this one from Barricade.

This is going to be a lot more durable than the stock fender flare being made of carbon

plated steel.

However, if you do take a hard enough hit, you will transfer some of that energy into

your body and essentially causing a little bit more damage than you might want.

Nonetheless, if you are in favor of this tubular option, then it will be a more durable setup

overall, and will also come with a black powder coat finish to resist any of that rusting

or corrosion.

This will also be a flat flare.

So when you're off-road, you're going to get a lot more articulation and up travel out

of this flare than you would the stock.

Not to mention, you are going to get a very aggressive and off-road look with these new

fender flares.

So enough about the stock fender flare, let's put on our Barricades.

So now, we can bolt up our Barricade to the fender.

They provided us with a notch here, so we can rest the fender on this bracket and bolt

up our hardware.

So after it's resting on this bracket, we can loosely attach our hardware.

And the reason why we loosely attach it is so we can shimmy the fender around to get

in all of the other bolts.

So now that all of our hardware is in and everything's lined up, we can tighten everything

down with an extended Allen key, it's going to be a 5-millimeter, and a 13-millimeter

wrench.

So once our hardware is loosely installed, we can take our rubber gasket with the flat

side facing the inside of the Jeep and insert it in between the body and the fender.

So once we have it where we want it, we can cut our excess off so we can use it on the

other side.

And this is going to give the fenders a more finished look and protect the paint on your

body.

So with our gasket installed, we can tighten all of our hardware using a 5-millimeter Allen

key and a 13-millimeter wrench.

So after we have our fender all buttoned up, we can do the same thing on the other side

and then move to the rear.

So unlike the front, we can only access two of the bolt holes, so Barricade provided us

with rivnuts to be inserted in the rest of the holes.

So, with the help of a friend holding the flare, we're going to loosely install our

hardware.

So, with all of our hardware loosely installed, just like the front, we're going to install

our gasket and then tighten everything down.

For the bolts with the rivnuts, you're going to be using a 4-millimeter Allen key.

And for the bolts with the nuts on the back, you can use a 5-millimeter Allen key and a

13-millimeter wrench.

So, after everything's tightened down, then you're all set to go.

That's it for my review and install on the Barricade tubular fender flares fitting all

'07 to '18 two-door and four-door JKs.

For more videos like this, keep it right here at extremeterrain.com.