Thứ Tư, 30 tháng 5, 2018

Auto news on Youtube May 30 2018

Dear friends Hello

today we have a machine in the volvo s60 and climb the Parking brake

the car came with the symptoms of the wheel wedging this fault

manifested itself when moving back when you go back

is the grinding noise and feel the wheel brakes in the first place in this situation, the suspicion falls on either

brake pads are either on the Parking brake or handbrake pads after I took off the wheel

razvel kolodochki realized that something is getting in the way inside the drum when I took the drum saw the following picture

the pads were in this state that is lining

flew off the pads and moved freely inside the drum

according to the old tradition, turn to the type of species says to remove the decorative cover of the handbrake in the cabin and there will be access to

adjusting screw loosen the screw at 5 10 turns to loosen the cables then remove the wheel

remove the brake Assembly remove the brake disc and

remove the insides of the brake pads, springs that hold it all then change all to new and assemble in reverse order

how to adjust the handbrake, I will tell at the end when we are already engaged in the adjustment directly

cardan balance offers factory repair diagnostics balancing and manufacturing of cardan shafts of any complexity on modern equipment

please call 8 800 555 50 37

cardan balance

if dorustilavat and models it was possible to pull the sidewall in the restyled model

here it goes on torx mounted and

to get to the adjustment screw you need a little differently

now and try the camera so as not to offend

sashlock sashlock here, here and here three pins which are inserted

we remove the cover of the handbrake and get access to the nut here it is now the adjustment will show you better

here she and the Unscrew the nut 5 at 10 rpm

here are such a slits that do not give her to turn now I let go of the maximum cable handbrake and

you can proceed with the dismantling and subsequent installation

handbrake

so last time I took everything off and left disassembled now is only all to collect and put in place

put the spring and be sure to collect a bunch of wires that I uncovered

do not forget about the plugs

so dear friends now I'll start the car the car in the sun let the air conditioner work a little bit in the first place

pumping the pedal

brakes

all pads come up

a little cool in the cabin and so now

here on the new pads

it makes three clicks

means as says species maximum effect and should be between the second and the fifth clicking here is and 1

2 and 3 this here is he already well 4 already such

hard tension yet leave because there's a little wheel in the grinding and spinning

we have a ride that is kind of at the beginning asks when the very unscrewed this bolt adjusting

pull it up so that there were 2 to 5 clicks we have just two three four here are four clicks

then you need to take a ride and at a speed of 30 kilometers of the hour to start braking handbrake to pads

got used to the drum so they caught my place is here on the user view says

ride

could get a little brake view behaves like the handbrake should pull up then come view if freely spinning wheel

the road is not very good food slowly to the camera fell

accelerated to 30 start braking

overclocked a little will drop about 30

the first time was quite hard the second time already better stops the car

in General, as it kind of says what needs to be done once at least she only writes about one episode but I already do here

a little in its own way

now a couple of times so the machine will slow down to the handbrake pads

got used better and in principle we will already get up on the platform raise the wheel look at how it turns in free condition

check for clicks on the handbrake

so again accelerated slightly 30 about

already gives 6 clicks 7 clicks 8 even

Yes the handbrake

the handbrake slipped it well

here already on a bad road both wheels are on the SW when braking

Yes camera fell sorry

so it was in shade

the machine let the air conditioner work still saves the heat on the street

one two three 4 5 and that's only on the fifth force felt 6

so put on 3

on 2 and on 3 is already tight do not know to write so as not to leave

3 is the fixation of think a little bit will go

here is the fourth already quite tight, probably leave

in that position

but the case how to insert I told you so one here is the second

here's the third but here the main two from the top of two loops here are the bottom three

the pin that are inserted will go to lift the machine and

cheers.

watch whether the wheel is spinning at all when the handbrake is released

the wheel spins great a little clasp that hold it

this is not critical

after the first kilometer of the ride

this hook will not be what dear friends thank you for watching this video to the end

easy easy repairs to you all the best until we meet again

Không có nhận xét nào:

Đăng nhận xét